Standard Drawings
The Standard Drawings on this website have been adopted by Council for use within the Noosa local government area. Please contact Council if you wish to use a different revision than those on this website.
Addendums to the Standard Drawings must be adhered to meeting the requirements of the Noosa Planning Scheme Policies and Noosa Design Principles:
- Support Noosa's environmental objectives with plantings that enhance biodiversity.
- Provide a transport network that caters to the needs of the community and blends into the environment rather than dominating it.
- Design for pedestrians, cyclists and buses in all road corridor improvements.
- Design to cater for the aged and disabled community.
Please refer to the following documents:
Roads
Driveways
Pathways
Std Drawing No. |
Description |
Addendum |
RS-065(PDF, 108KB) |
Concrete pathway construction details |
Yes |
Kerb and channel
Public utilities
Signs
Subsoil drains
Pavement Extension
Public transport
Drainage
Access Chamber
Bedding and backfilling
Std. Drawing No. |
Description |
Addendum |
DS-030(PDF, 195KB) |
Excavation, bedding and backfilling of stormwater drainage pipes |
No |
DS-031(PDF, 76KB) |
Excavation, bedding and backfilling precast box culverts |
No |
Sediment control devices
Std. Drawing No. |
Description |
Addendum |
ESC-01 |
Rock pads for building sites |
No |
ESC-02 |
Grated stormwater (field) inlet sediment traps |
No |
ESC-03 |
Kerb inlet sediment traps |
No |
ESC-04 |
Sediment fence |
No |
ESC-05 |
Sediment fence - notes |
No |
Drainage pits
Culverts
Std. Drawing No. |
Description |
Addendum |
MR-1174(PDF, 136KB) |
RC Box culvert - construction of end structures H = 150 - 600 |
No |
MR-1243(PDF, 673KB) |
Precast headwall (1 of 2) |
No |
MR-1303(PDF, 275KB) |
RC Box culvert - construction of reinforced concrete wingwalls and headwalls |
No |
MR-1304(PDF, 542KB) |
Construction of reinforced concrete wingwalls and aprons for pipe diameter up to 2400 |
No |
MR-1305(PDF, 314KB) |
General arrangement and installation of wingwalls and aprons for pipe diameter 375-675 diameter |
No |
MR-1316(PDF, 216KB) |
General arrangement and installation of precast units |
Yes |
MR-1317 Rev H(PDF, 357KB) |
Construction of bases with nibs and aprons |
Yes |
MR-1318 Rev G(PDF, 335KB) |
Construction of bases with recesses and aprons |
Yes |
MR-1319 Rev I(PDF, 209KB) |
Construction of reinforced wingwalls and RC headwalls H + 750 - 2400 |
No |
MR-1320 Rev C(PDF, 149KB) |
Crown unit holding down anchors |
No |
Addendums
Driveways
Std. Drawing No. |
Description |
RS-049(PDF, 66KB) |
provide for min 2.0m wide concrete pathway at max 2.5% cross fall |
RS-050(PDF, 103KB) |
provide for min 2.0m wide concrete pathway at max 2.5% cross fall |
RS-051(PDF, 67KB) |
General Type Preferred. Provide for min 2.0m wide concrete pathway at max 2.5% crossfall. |
RS-056(PDF, 112KB) |
Noosa Council has not adopted Revision G. Please use Revision F available above under Roads.
Min. 1.5m of driveway abutting into existing road edge to be flexible pavement |
RS-056 and RS056.1(PDF, 1MB) |
Rural driveway (Concrete Alternative) |
Pathways
Std. Drawing No. |
Description |
RS-065(PDF, 108KB) |
Pathway widths:
Off road trunk pathways – minimum 2.5m, desirable 3.0m or full width in commercial precinct. Absolute minimum 1.5m at squeeze points only.
- Arterial - minimum 2.5m, desirable 3.0m
- Distributor - minimum 2.0m, desirable 3.0m
- Collector - minimum 1.8m, desirable 2.4m
- Local - minimum 1.5m, desirable 2.0m.
Concrete specification:
- 1.5m - 2.5m wide pathway – 32Mpa, 125mm, SL72 mesh centrally
- >2.5m wide pathway - 32Mpa, 150mm, SL82 mesh centrally
|
Utilities
Std. Drawing No. |
Description |
RS-100(PDF, 114KB) |
Typical service corridors and alignments are for new developments only. In brownfield sites maintain existing alignments where necessary. |
Signs
Std. Drawing No. |
Description |
RS-130(PDF, 68KB) |
White lettering on Noosa green background. No logo. Street numbers optional. If street numbers are not used, sign plate to be 150mm high with 100mmm high lettering. |
RS-131(PDF, 74KB) |
Sign posts to be installed using typical post anchor or Loc-socket only. |
IS 10 |
J pole sign posts to be installed using V-sockets or Lock-sockets. When adjacent to pathway the mounted height of the sign is 2.5m to allow for cyclists. |
Sediment Control
Std. Drawing No. |
Description |
IECA |
REFER to International Erosion Control Association |
Drainage pits
Std. Drawing No. |
Description |
DS-060, DS-061, DS-062, DS-063, DS-068 |
Preferred Kerb inlet is Noosa 9223 with environmental message where possible.Inlet capacity charts are available on request |
Landscape
Std. Drawing No. |
Description |
GS-011 and GS-012 |
Median kerb type to be SM3 with 300mm wide coloured concrete backing strip |
GS-041, GS-044, GS045 |
Black only PVC mesh, posts to be painted black or as specified by Council. |